Kenwood NX-5400-ISCK2 Intrinsically Safe 700/800MHz 3-Watt NXDN, DMR Digital Radio With Display and Limited Keypad
Kenwood's NX-5000 Series offers unsurpassed interoperability for a wide variety of users as it supports three digital CAIs — NXDN, DMR and P25 (Phase 1 & 2) — plus FM analog in a single radio. Best of all, a desired CAI can be selected at will, giving you the freedom to migrate at your own pace — whether you are intent on going fully digital, undecided about which digital system to pick, or just wanting to maintain both digital and analog for a while. An NX-5000 radio can simultaneously support two digital protocols plus analog, offering the following combinations: FM/DMR/ NXDN, FM/NXDN/P25, and FM/DMR/P25.
Feature Overview:
- MULTI-Digital operation in NXDN protocols
- Mixed Digital & FM Analogue Operation allows intelligent migration in mixed sites and easy migration with digital radios in other sites
- Large, Color 1.74" (240 x 180 pixels) Transflective TFT Display for better interface even in direct sunlight and with use of polarized sunglasses.
- Easy to follow GUI for at-a-glance operational status checking and Multi-line Text to access more information
- 4-way Directional-pad (D-pad) and 2-Position Lever Switch for intuitive control and operation
- Built-In GPS Receiver/Antenna for effective fleet management
- Bluetooth® Module built-in for hands-free operation
- Renowned KENWOOD Audio Quality can be achieved with Active Noise Cancelling that utilizes built-in DSP with two microphones for suppression of ambient noise
- Built-in 56-bit DES Encryption
- Optional 256-bit AES Encryption
- Built-in Motion Sensor for life-critical man down detection
- microSD/microSDHC Memory Card Slot for increased memory capacity for “Voice & Data”
- IP67/68 and MIL-STD-810 C/D/E/F/G
Digital - NXDN Mode:
- NXDN® Conventional
-
NXDN® TYPE-C (Gen1/Gen2) Trunking (only in 800MHz)
-
AMBE+2TM VOCODER
-
6.25 & 12.5 kHz Channels
-
Over-the-Air Alias
-
Over-the-Air Programming
-
Paging Call
-
Emergency Call
-
All Group Call
- Digital Two-Tone
- Status Messaging
- Remote Stun/Kill/Check
- Short & Long Data Messages
- GPS Location
- NXDN® Scrambler
Digital - DMR Mode:
- DMR Tier 2 Conventional Option
- S-Trunking Option
- DMR Tier 3 Trunking Option
- DMR Auto Slot Select (DASS)
- AMBE+2TMVOCODER
- 12.5 kHz Channels
- Over-the-Air Programming
- Call Interrupt (Direct & Repeater Mode) • Paging Call
- Emergency Call
- All Group Call
- Late Entry
- Status Messaging
- Remote Control by Subscriber Units
- ARC4 Encryption Optional
- Site Roaming
Analog Mode:
- NPSPAC Channels
- Conventional Zones
- LTR® Zones
FleetSync - FleetSync®/II: PTT ID ANI, Caller ID Display, Selective/Group Call, Emergency Status,Text Messages
- MDC-1200: PTT ID ANI, Caller ID Display, Emergency, Radio Check & Inhibit QT / DQT
- Two-Tone (Conventional Zones Only)
Contact Two Way Direct to Stay Connected
Once you’ve received your Kenwood NX-5400-ISCK2 two-way radio and start putting them to use on the job, you know you’ll have the support of a leading company for troubleshooting and recommendations of compatible accessories. Order with Two Way Direct for:
- The Lowest Price Guaranteed
- 24/7 Customer Support
- Low shipping costs – with free ground shipping
Use this Kenwood NX-5400-ISCK2 two-way radio with complete confidence. Order online or call 888-742-5893.
| Product Type: | Handheld Radios |
| Technology: | Digital & Analog (NXDN) |
| Compatible With (Brand): | Kenwood |
| Frequency Band: | 700/800MHz |
| Channels: | 1024 Channels |
| Power Output: | 3-Watts |
| Display: | Yes |
